Hornby HM2000 Twin Controller Transformer (R8012)

Recommended for expanding model railways

An excellent twin-track power controller unit, with power outputs for accessories provided, allowing point motors to be connected without needing another power supply. The power transformer is incorporated into the controller, it has a 240-volt AC power cable and plug attached and the transformer is built in.

Connects to mains and provides high output speed control for two loco's on separate tracks - extendable to four by adding extra slave control units. 16v AC & 12v DC power outputs for signals and lights are also provided.

This is the one! A good standard railway controller that is capable of providing power for most normal (analogue) model railway layouts.

Bachmann 12v Power Controller with Transformer (36-560)

Recommended single-track train controller.

A 12-volt DC single track controller, analogue, supplied with a plug-top mains power transformer, track power wire.
The controller has a large knob for speed control and a long flat slide switch for direction control, making running the trains easy and fun for children and adults alike. Will control all standard locomotives from Hornby, Bachmann, Graham Farish, Dapol and most other manufacturers.

Output 12V DC controlled, 0.7Amps

Please note that due to irregular supply of retail packed controllers we occasionally supply these controllers unboxed to reduce the delay until retail packaged items are available again.

Hornby Single Track Train Controller (R8250)

Low cost train controller allowing forward and reverse? with proportional speed control. Requires a 16v AC input from a Hornby C9200 plug in wall transformer. The output is 12v DC controlled plus it has a 16v output for operating points, signals etc.

An inexpensive starter option.

Requires C990 mains transformer.

Gaugemaster Model Combi - Single track Controller (COMBI)

An uncomplicated controller which comes complete with a separate, dedicated transformer plugging directly into a wall socket with a 1.8m lead to plug into the controller. The Combi can be screwed to either a panel or direct to the baseboard. This means that small layouts which have to be put away will not be encumbered with trailing wires & heavy transformers. The casings are made from high impact ABS & the control circuits give the same running characteristics as our traditional controllers.
The transformer is available separately as model WM1.

Gaugemaster Model D Twin Track Controller (D)

Gaugemaster Model HH - Walkabout Unit with Feedback (HH)

Single track hand-held or walkabout type controller with feedback, suitable for most small gauges.
Input:1 x 16v A.C. at a maximum of 1.25 amps Requires T1, M1 Transformer, or 100M Controller
Output: 1 x 12v D.C. at 1 amp controlled
Measurements: 75mm x 50mm x 27mm deep
Fitted with 1.5 metres of 4 core cable

Not recommended for use with coreless design motors

Gaugemaster Model WS - Walkabout Unit with Inertia (WS)

Gaugemaster Pair of Pin + Ring Terminated leads. (GM12)

Gaugemaster Wall Mounted Transformer 1x 18vAC/1amp (WM1)

The casing is made from high impact ABS
Input: Mains (240v A.C.)
Output: 1 x 18v A.C. at 1.1 amp
Measurements: 65mm x 80mm x 83mm

Gaugemaster Model T1 -Transformer 2x 16v AC/1.25amps (T1)

A useful AC transformer ideal for providing power for controllers and point motor supplies. Two 16-volt output windings are provided at a maximum output of 1.25amps.

Please note that this transformer must be installed inside an? enclosure suitable for mains power use.

? 

Gaugemaster Model T2 - Transformer 1x 18v AC/2.5 amp (T2)

Gaugemaster Model T3 -Transformer 1x 24v AC/1.25amps (T3)

Gaugemaster Model T5 Transformer 1x12v AC/5amp (T5)

Open Construction Transformer
Input: Mains (240v A.C.) use 3 amp fuse
Requires own mains lead & plug to be fitted
Output: 1 x 12v A.C. at 5 amps
Requires own wires and cutouts as necessary

Gaugemaster Ring Terminals x6 (GM15)

Gaugemaster Booster Transformer (BOOSTER)

Gaugemaster Pin Type Connectors x 6 (GM14)

Gaugemaster Model M1 - Cased Transformer 2x16v AC/1amp (M1)

Hornby Multi-Purpose Mains Plug Type Transformer (P2000)

Standard 16v AC wall mounted plug top transformer unit. This is the power supply for Hornby R965 train controller and Scalextric racing powerbase controllers.