Contact Mail Order Hotline on 01453 825 381 or email enquiries@antics.ltd.uk
0 Items
Subtotal: €0.00
checkout
> Power & Electrics > DCC Digital Control > Static Accessory Decoders

more

Bachmann Dynamis DCC Decoder for Accessories 36-561

Accessory decoder with four outputs for control of points, signals, etc. Each output can be configured for continuous or pulse output, allowing solenoid (pulse) or motor-driven (continous) point motors to be driven. Two of the outputs can also be configured to drive standard RC servo motors.

Complies with NMRA DCC standards. Suitable for use with all NMRA compliant DCC digital command control systems. A DCC command station will be required.


more...
Stock:
Available from shops: Bristol: 1(explain)
(Prod Ref #71986)
MRP: €53.51
Antics Price: €47.20


more

Lenz LS100 Switch Module 4 Points/Signals Feedback 11100

The accessory decoder receives the commands send by the central command station through the power module and, for example, controls the switch machines on your turnouts (or the other devices). The commands are initiated from your input devices, such as the Basic Hand Held LH100, the Tower Cab LW100, the Computer Interface LI100 or the command station converter module LC100 (in connection with an Arnold or M rklin Digital system). The accessory decoder LS100/LS110 are equipped with 4 outputs, with 3 terminals (+,C,-) each. These outputs can be connected to 4 twin-coil switch machines (or twin-coil actuators for your signals).
more...
Stock:
Pre-Order (Website:0)(explain)
(Prod Ref #51789)
Price: €84.96


more

Hornby OO DCC Point Conversion Clips R8232

These clips are designed to fit into Hornby points to convert the point for DCC operation. The clip feeds track power through the point, keeping both diverging tracks live at all times.

Pack of 20


more...
Stock:
Available from shops: Gloucester: 1(explain)
(Prod Ref #61026)
Price: €5.01


more

Hornby OO Digital Power Connecting Clip R8242

Hornby track power connector clip designed for use with digital control systems.

For connecting the R8216 Point / Accessory Decoder to track


more...
Stock:
Pre-Order (Website:0)(explain)
(Prod Ref #63066)
Price: €3.53


more

ANEmodel OO DCC SmartSwitch Point Operation Set A003

This DCC version of the ANEmodel Smart Switch takes power from the DCC track power source (rails or power bus lines) allowing local installation. Supplied with control toggle switches as standard a SmartSwitch decoder will be available soon, allowing for DCC control signals to be used as an alternative. The SmartSwitch provides an excellent flexible solution to remote point control using a programmable four-switch control board with outputs for highly controllable servo motor machines. The servo motors can be installed under or above the baseboard with the drive arranged in several ways to activate points, semaphore signals or level crossing gates.
The board also provides for feedback outputs to power indicator LEDs on a control panel. Points are activated from a control panel using change-over toggle switches (supplied) or the board can be programmed to accept a signal from a push-to-make button switch. Due to the low currents needed for these command signals multi-way computer ribbon cabling can be used to keep wire runs tidy for connection to centralised control panels. Additional servo extension leads are readily available, these are the same leads as used by RC modellers.
For use with insulated frog or power-routing points. For live frog points requiring power feeds a SmartFrog polarity switching unit will soon become available.

Economical - the set includes all the equipment to operate four points. Everything is in the set - wiring, servos, switches and the Smartswitch control board. This compares very favourably in cost to other slow motion point control systems on the market.
Ultimate flexibility - Smartswitch can not only operate points but also crossing gates, semaphore signals or any creative animation you can think of.
Easy to install - Built in drilling template and virtual centre line for easy trouble free mounting PLUS more mounting options: central, off centre or horizontal, above or below the baseboard.
Nine adjustable servo speeds - the SmartSwitch control board gives you a wide choice of servo speeds. You can operate your points with a snap action or in scale slow speeds.
Control board can control up to four servos - plus you can simultaneously control up to four servos using just one switch.
SmartSwitch remembers the point positions when the power is off.
Low current drain - operates from 9 to 25v DC (an on-board rectifier allows use of the DCC system AC power)

more...
Stock:
Available Soon (Website:0)(explain)
(Prod Ref #86251)
Price: €100.30

> Power & Electrics > DCC Digital Control > Static Accessory Decoders
 
Antics on-line with model shops in: Stroud (HQ), Bristol, Cardiff, Gloucester, Sheffield, Plymouth, Worcester and Coventry.
We stock a full range which includes plastic kits, radio control cars, diecast models, railways, planes and boats etc.
Click on the links under "Available to buy now" or any picture in order to start shopping. Offers subject to availability. E&OE.
Jatech Limited