more | Radio Active 7" Prop Shaft And 3bl Propellor 30mm (RMA3047)
These low-cost shaft, tube and prop assemblies are great for school projects and scout groups, or any other to small electric powered boat applications. Each features a brass tube with glass filled nylon bearings and 2mm shaft. | |
more | Perkins Boat Prop Shaft 5" M4 Thread (5511130)
These steel shaft propeller shafts are supplied with a 4mm metric thread and with a brass bushed tube of 8mm diameter. Each end has a 4mm thread, nut and washer. To seal the shaft pack with vaseline or thick grease. The length quoted relates to the tube length, the shaft protrudes 1" from the tube. | |
more | Perkins Boat Prop Shaft 6" M4 Thread (5511135)
These steel shaft propeller shafts are supplied with a 4mm metric thread and with a brass bushed tube of 8mm diameter. Each end has a 4mm thread, nut and washer. To seal the shaft pack with vaseline or thick grease. The length quoted relates to the tube length, the shaft protrudes 1" from the tube | |
more | Perkins Boat Prop Shaft 7" M4 Thread (5511145)
These steel shaft propeller shafts are supplied with a 4mm metric thread and with a brass bushed tube of 8mm diameter. Each end has a 4mm thread, nut and washer. To seal the shaft pack with vaseline or thick grease. The length quoted relates to the tube length, the shaft protrudes 1" from the tube | |
more | Perkins Boat Prop Shaft 8" M4 Thread (5511150)
These steel shaft propeller shafts are supplied with a 4mm metric thread and with a brass bushed tube of 8mm diameter. Each end has a 4mm thread, nut and washer. To seal the shaft pack with vaseline or thick grease. The length quoted relates to the tube length, the shaft protrudes 1" from the tube | |
more | Perkins Boat Prop Shaft 9" M4 Thread (5511155)
These steel shaft propeller shafts are supplied with a 4mm metric thread and with a brass bushed tube of 8mm diameter. Each end has a 4mm thread, nut and washer. To seal the shaft pack with vaseline or thick grease. The length quoted relates to the tube length, the shaft protrudes 1" from the tube | |
more | Perkins Boat Prop Shaft 10" M4 Thread (5511160)
These steel shaft propeller shafts are supplied with a 4mm metric thread and with a brass bushed tube of 8mm diameter. Each end has a 4mm thread, nut and washer. To seal the shaft pack with vaseline or thick grease. The length quoted relates to the tube length, the shaft protrudes 1" from the tube. | |
more | Perkins Boat Prop Shaft 11" M4 Thread (5511165)
These steel shaft propeller shafts are supplied with a 4mm metric thread and with a brass bushed tube of 8mm diameter. Each end has a 4mm thread, nut and washer. To seal the shaft pack with vaseline or thick grease. The length quoted relates to the tube length, the shaft protrudes 1" from the tube | |
more | Perkins Boat Prop Shaft 12" M4 Thread (5511170)
These steel shaft propeller shafts are supplied with a 4mm metric thread and with a brass bushed tube of 8mm diameter. Each end has a 4mm thread, nut and washer. To seal the shaft pack with vaseline or thick grease. The length quoted relates to the tube length, the shaft protrudes 1" from the tube | |
more | Radio Active Marine Propellor 35mm 2BL L/H (4mm) (RMA3030)
Using a standard blade pattern, these glass-filled nylon props have a much higher strength and rigidity than their nylon counterparts making them ideal for use with high power marine engines. Each prop features a moulded-in brass insert. | |
more | Radio Active Marine Propellor 40mm 2BL L/H (4mm) (RMA3031)
Using a standard blade pattern, these glass-filled nylon props have a much higher strength and rigidity than their nylon counterparts making them ideal for use with high power marine engines. Each prop features a moulded-in brass insert. | |
more | Radio Active Marine Propellor 45mm 2BL L/H (4mm) (RMA3032)
Using a standard blade pattern, these glass-filled nylon props have a much higher strength and rigidity than their nylon counterparts making them ideal for use with high power marine engines. Each prop features a moulded-in brass insert. | |
more | Radio Active Marine Propellor 50mm 2BL L/H (4mm) (RMA3033)
Using a standard blade pattern, these glass-filled nylon props have a much higher strength and rigidity than their nylon counterparts making them ideal for use with high power marine engines. Each prop features a moulded-in brass insert. | |
more | Radio Active Marine Propellor 35mm 2BL L/H (4mm) (RMA3007)
This series is moulded in glass-filled nylon for improved strength and stiffness. Again, ideal for high speed electric and performance I/C drives and fast planing hulls. Moulded-in tapped brass inserts. | |
more | Radio Active Marine Propellor 40mm 2BL L/H (4mm) (RMA3008)
This series is moulded in glass-filled nylon for improved strength and stiffness. Again, ideal for high speed electric and performance I/C drives and fast planing hulls. Moulded-in tapped brass inserts. | |
more | Radio Active Marine Propellor 45mm 2BL L/H (4mm) (RMA3009)
This series is moulded in glass-filled nylon for improved strength and stiffness. Again, ideal for high speed electric and performance I/C drives and fast planing hulls. Moulded-in tapped brass inserts. | |
more | Radio Active Marine Propellor 50mm 2BL L/H (4mm) (RMA3010)
This series is moulded in glass-filled nylon for improved strength and stiffness. Again, ideal for high speed electric and performance I/C drives and fast planing hulls. Moulded-in tapped brass inserts. | |
more | Radio Active Marine Propellor 55mm 2BL L/H (4mm) (RMA3012)
Designed for maximum performance when using high powered electric or I/C drives. These waterscrews, with their high pitch 'X' pattern blade shape, are ideal for fast planing hulls, and feature moulded-in brass inserts. | |
more | Radio Active R/C Rudder Micro c/w Tiller Arm (RMA3061)
Shiny brass rudders with brass rudder posts sleeved with a threaded glass filled nylon bearing tube. All brass nuts and retaining washers are supplied, together with a strong, glass filled nylon tiller arm. Available in six sizes to suit a wide variety of applications. Post Length 40mm. | |
more | Radio Active R/C Rudder Mini c/w Tiller Arm (RMA3062)
Shiny brass rudders with brass rudder posts sleeved with a threaded glass filled nylon bearing tube. All brass nuts and retaining washers are supplied, together with a strong, glass filled nylon tiller arm. Available in six sizes to suit a wide variety of applications. Post Length 50mm. | |
more | Radio Active R/C Rudder Small (RMA3063)
Shiny brass rudders with brass rudder posts sleeved with a threaded glass filled nylon bearing tube. All brass nuts and retaining washers are supplied, together with a strong, glass filled nylon tiller arm. Available in six sizes to suit a wide variety of applications. Post Length 50mm. | |
more | Radio Active R/C Rudder Medium (RMA3064)
Shiny brass rudders with brass rudder posts sleeved with a threaded glass filled nylon bearing tube. All brass nuts and retaining washers are supplied, together with a strong, glass filled nylon tiller arm. Available in six sizes to suit a wide variety of applications. Post Length 50mm. | |
more | Radio Active R/C Rudder Large (RMA3065)
Shiny brass rudders with brass rudder posts sleeved with a threaded glass filled nylon bearing tube. All brass nuts and retaining washers are supplied, together with a strong, glass filled nylon tiller arm. Available in six sizes to suit a wide variety of applications. Post Length 65mm. | |
more | Radio Active R/C Rudder Extra Large (RMA3066)
Shiny brass rudders with brass rudder posts sleeved with a threaded glass filled nylon bearing tube. All brass nuts and retaining washers are supplied, together with a strong, glass filled nylon tiller arm. Available in six sizes to suit a wide variety of applications. Post Length 65mm. | |
more | Radio Active Rx Aerial Detatchable Boat/Car (RGA2007)
Neaten your R/C installation with one of these deck mounted aerials. This whip aerial replaces the receiver's standard aerial with a removeable piano wire whip aerial. | |
more | Radio Active Water Scoop & Outlet (RMA3060)
Water scoops allow for easy water cooling of electric motors, electronic speed controllers, or even I/C engines. The scoop needs to be fitted behind the propeller, so the prop wash is forced up the tube, the handy water tight exit tube is then fitted on the rear of the hull. with a length of silicone tube fitted in between the two, and passing the item to be cooled, this is a sure fire way to eliminate overheating. | |
more | Radio Active Tiller Arm (RCA132)
These tiller arms are moulded in glass filled nylon, with multiple mounting holes for adjustment. The closer to the centre that you connect your linkage, the less movement you'll get out of the rudder. | |
more | Ripmax Dyco Coupling Unit (DC1)
Dyco Couplings offer a flexible solution to joining marine propeller shafts to your electric motor. A flexible solution in more than one way, as the brass inserts are supplied seperatly so as to allow the builder to select the correct size for the job. | |
more | Ripmax Dyco Coupling Insert M4 Threaded (DT64)
Dyco Couplings offer a flexible solution to joining marine propeller shafts to your electric motor. A flexible solution in more than one way, as the brass inserts are supplied seperatly so as to allow the builder to select the correct size for the job. | |
more | Ripmax Dyco Coupling Insert M5 Threaded (RMA5640)
Dyco Couplings offer a flexible solution to joining marine propeller shafts to your electric motor. A flexible solution in more than one way, as the brass inserts are supplied seperatly so as to allow the builder to select the correct size for the job. | |
more | Ripmax Dyco Coupling Insert M6 Threaded (DT66)
Dyco Couplings offer a flexible solution to joining marine propeller shafts to your electric motor. A flexible solution in more than one way, as the brass inserts are supplied seperatly so as to allow the builder to select the correct size for the job. | |
more | Ripmax Dyco Coupling Insert 4BA Threaded (DT20)
Dyco Couplings offer a flexible solution to joining marine propeller shafts to your electric motor. A flexible solution in more than one way, as the brass inserts are supplied seperatly so as to allow the builder to select the correct size for the job. | |
more | Ripmax Dyco Coupling Insert 2BA Threaded (DT22)
Dyco Couplings offer a flexible solution to joining marine propeller shafts to your electric motor. A flexible solution in more than one way, as the brass inserts are supplied seperatly so as to allow the builder to select the correct size for the job. | |
more | Ripmax Dyco Coupling Insert 1/4unf Threaded (DT50)
Dyco Couplings offer a flexible solution to joining marine propeller shafts to your electric motor. A flexible solution in more than one way, as the brass inserts are supplied seperatly so as to allow the builder to select the correct size for the job. | |
more | Ripmax Dyco Coupling Insert 2.3mm Plain (DP33)
Dyco Couplings offer a flexible solution to joining marine propeller shafts to your electric motor. A flexible solution in more than one way, as the brass inserts are supplied seperatly so as to allow the builder to select the correct size for the job. | |
more | Ripmax Dyco Coupling Insert 2mm Plain (DP32)
Dyco Couplings offer a flexible solution to joining marine propeller shafts to your electric motor. A flexible solution in more than one way, as the brass inserts are supplied seperatly so as to allow the builder to select the correct size for the job. | |
more | Ripmax Dyco Coupling Insert 3mm Plain (RMA5565)
Dyco Couplings offer a flexible solution to joining marine propeller shafts to your electric motor. A flexible solution in more than one way, as the brass inserts are supplied seperatly so as to allow the builder to select the correct size for the job. | |
more | Ripmax Dyco Coupling Insert 4mm Plain (DP34)
Dyco Couplings offer a flexible solution to joining marine propeller shafts to your electric motor. A flexible solution in more than one way, as the brass inserts are supplied seperatly so as to allow the builder to select the correct size for the job. | |
more | Ripmax Dyco Coupling Insert 5mm Plain (DP35)
Dyco Couplings offer a flexible solution to joining marine propeller shafts to your electric motor. A flexible solution in more than one way, as the brass inserts are supplied seperatly so as to allow the builder to select the correct size for the job. | |
more | Ripmax Dyco Coupling Insert 1/8 (DP12)
Dyco Couplings offer a flexible solution to joining marine propeller shafts to your electric motor. A flexible solution in more than one way, as the brass inserts are supplied seperatly so as to allow the builder to select the correct size for the job. | |
more | Ripmax Dyco Coupling Insert 3/16" Plain (DP13)
Dyco Couplings offer a flexible solution to joining marine propeller shafts to your electric motor. A flexible solution in more than one way, as the brass inserts are supplied seperatly so as to allow the builder to select the correct size for the job. | |
more | Ripmax Dyco Coupling Insert 1/4" Plain (DP14)
Dyco Couplings offer a flexible solution to joining marine propeller shafts to your electric motor. A flexible solution in more than one way, as the brass inserts are supplied seperatly so as to allow the builder to select the correct size for the job. | |
more | Ripmax Dyco Coupling Insert 3/32" plain (DP10)
Dyco Couplings offer a flexible solution to joining marine propeller shafts to your electric motor. A flexible solution in more than one way, as the brass inserts are supplied seperatly so as to allow the builder to select the correct size for the job. | |
more | Ripmax Dyco Grub Screw M3 (DGS1)
Dyco Couplings offer a flexible solution to joining marine propeller shafts to your electric motor. A flexible solution in more than one way, as the brass inserts are supplied seperatly so as to allow the builder to select the correct size for the job. | |
Antics
Search
Index
Checkout
Back