Contact Mail Order Hotline on 01453 825 381 or email enquiries@antics.ltd.uk
0 Items
Subtotal: £0.00
checkout
> Power & Electrics > Digital Command Control (DCC) > DCC Control Units

More info

NCE The Power of DCC Power Cab 2 amp DCC Digital Command Control Starter Set 5240042

NCE The Power of DCC Power Cab 2 amp DCC Digital Command Control Starter Set 5240042
An entire DCC system in the palm of your hand! This 2 Amp system can operate up to 4 HO sized locomotives or 8 N scale trains. This cab provides all of the capability and ease of use that you?ve heard about in our Power Pro system, at an entry level price. Installation is a snap. Hook two wires to your track and plug in the cab. You?re off and running trains!
The Power Cab kit contains: Power Cab, 7' Power Cab Cable, PCP Power Panel, EU / UK Approved Power Supply, Pro Cab Coiled Cord, and Manual.
Read more...
Stock:
Website: 2
Available from shops: Bristol: 1, Cardiff: 1, Coventry: 1, Plymouth: 1, Stroud: 1(explain)
(Prod Ref #100964)
MRP: £170.65
Antics Price: £140.00


More info

Bachmann E-Z Command DCC Digital Controller 36-500

Ideal for train sets and small layouts!
Bachmann E-Z Command DCC Digital Controller 36-500
Straight-forward Digital Command Control that can run an entire layout for less than the cost of a twin track analogue controller! The EZ-Command can address up to 10 locomotives with sufficient power to run 2 or 3 OO locomotives at the same time.

The EZ-Command is ideal for new modellers and easy for children to use, locomotives are selected using push buttons 1-10, a replaceable insert allowing the recording of locomotive details beside each button. Decoder function can be activated in function control mode using the same ten buttons. Sound equiped locomotives have the core sounds and whistle/horn programmed to the low numbered functions, so these can be activated by the EZ-Command.

Basic programming is also very easy, once in programming mode locomotive addresses and default forward direction can be changed at the push of a button. Even experienced DCC operaters find the EZ-Command useful for their test-track controller.

Note - Locomotives must be fitted with a DCC decoder to be independently controlled.
The E-Z Command controller is also able to control one analogue locomotive, that is one not fitted with a decoder.


Read more...
Stock:
Website: 1(explain)
(Prod Ref #44835)
Price: £89.95


More info

Gaugemaster Prodigy Advance DCC Digital Command Control System DCC02

Gaugemaster Prodigy Advance DCC Digital Command Control System DCC02
Gaugemaster's Prodigy Advance DCC unit is one of the easiest to use and has been specifically taylored for the needs of the British modeller.

Antics Staff Uses this DCC Controller on Berkley Depot

Prodigy Advance conforms with NMRA standards and is compatible with all other leading manufacturers DCC accessories. Its strength is its simplicity without compromise and Prodigy Advance DCC will grow as your layout grows, allowing you to use the system at a level appropriate to your layout and style of operation.

Prodigy Advance DCC consists of a Base Station, a Walkaround Controller and a mains Power Supply - the complete package will enable you to digitally control your chipped locomotives within minutes. Wave goodbye to cab control, section switches and isolating sections - as just two wires from your Prodigy Advance base station run your whole railway in the way you want to without the normal constraints of conventional operation.

Prodigy system manuals and further information.


Read more...
Stock:
Pre-Order (Website:0)(explain)
(Prod Ref #77546)
MRP: £299.95
Web Only Price: £222.50


More info

Bachmann Dynamis Ultima Wireless DCC Digital Control System 36-504

Bachmann Dynamis Ultima Wireless DCC Digital Control System 36-504

Bachmanns' Dynamis system features a wireless control handset giving total freedom of operating or layout viwing location. Combined with a powerful DCC system designed by ESU, well known for their sound decoders. A centre-biased toggle joystick provides speed control and scroll control for locomotive selection, with up to 9999 decoder addresses available for locomotive or accessory control. A backlit LCD screen provides a graphical user interface with the ability to display a locomotive name or description. Dual banking of the 10 function buttons gives up to 20 function controls, exploiting the lighting functions and sound capabilities of current decoders.
The graphical displays make decoder programming and tuning easy, locomotives can be recalled and selected by name or number, with 2 and 4 digit addressing supported. Most CVs can be adjusted by selecting the CV number and value to be written using scroll up/down functionality.

Wiring your points for DCC control turns the Dynamis handset into a portable, wireless control panel for your entire layout!
Read more...
Stock:
Available from shops: Cardiff: 1, Plymouth: 1(explain)
(Prod Ref #63767)
MRP: £294.95
Antics Price: £240.00

stock
info

Bachmann Dynamis Railconrtoller Ultima DCC Digital Control System 36-504RCEB

Bachmann Dynamis Ultima DCC Digital Control System with Railcontroller Software (evaluation edition)

Includes a 30-day evaluation copy of Bachmanns' Railcontroller PC software and USB connection cable to allow decoder programming and layout control from a PC computer. Railcontroller holds loco performance profiles for all Bachmann Branchline locos, plus the ability to add and customise profiles for other locos. The track control features include WYSIWYG track diagram interface, when used with static (point) decoders pre-programmed routes can be set up and with track occupancy detectors automated signalling (up to 4 aspect signals) can be controlled.

The full Ultima hardware is supplied, so the system can be used with the suppl;ied controller handset in addition to the PC interface capability.

Bachmanns' Dynamis system features a wireless control handset giving total freedom of operating or layout viwing location. Combined with a powerful DCC system designed by ESU, well known for their sound decoders. A centre-biased toggle joystick provides speed control and scroll control for locomotive selection, with up to 9999 decoder addresses available for locomotive or accessory control. A backlit LCD screen provides a graphical user interface with the ability to display a locomotive name or description. Dual banking of the 10 function buttons gives up to 20 function controls, exploiting the lighting functions and sound capabilities of current decoders.
The graphical displays make decoder programming and tuning easy, locomotives can be recalled and selected by name or number, with 2 and 4 digit addressing supported. Most CVs can be adjusted by selecting the CV number and value to be written using scroll up/down functionality.

Read more...
Stock:
Available Soon (Website:0)(explain)
(Prod Ref #101381)
MRP: £299.95
Antics Price: £260.00


More info

Lenz Start Set 01 Digital Control System SET01

Lenz LH01 Start Set - Lenz' new entry level system.
The design is minimalistic in order to give the greatest functionality for the least price.
The LH01 Handset has a 4 digit display and one large control knob that works like a games consol control or a system control in a prestige car - the rotary knob can also be pressed in four directions and pressed in the middle so that you can enter the menus.  In this way Lenz can offer a high specification for a low price:

  • For up to 9999 digital motor vehicles
  • Setting of 4-digit locomotive addresses
  • 28 speed steps
  • 29 functions for each locomotive
  • Functions can be continuous or momentary by button press
  • 4 amp power supply
  • RailCom enabled programming in operational mode (PoM).  Standard POM can also be performed on decoders without RailCom
  • Separate programming track output
  • Double traction
  • connect up to 31 input devices to our universal input bus XpressNet.
  • points, signals and other magnetic articles can be switched.
  • Protected against short-circuit and overheat.

Each set comes with an LZV100 command station and an LH01 hand-held control device.
This set needs an additional Transformer.  There is the choice of the TR100 (3 Amp) or TR150 (5 Amp)
Read more...

Stock:
Website: 2(explain)
(Prod Ref #45288)
MRP: £249.95
Antics Price: £219.99


More info

Uhlenbrock Daisy II DCC System 2 amp 64300

Uhlenbrock Daisy II DCC System 2 amp 64300
Uhlenbrock 64300 Daisy II DCC System 2 amps

20 locomotives can be controlled simultaneously
9999 locomotive addresses
Data format DCC with 14, 28, and 128 speed steps for each locomotive address individually selectable
Up to 25 locomotive special functions per locomotive switchable (Software Version 2.0 now allows the full 29 functions)
Loco Names can be input and Loco symbols allocated
Loco functions can have symbols allocated
Up to 2000 solenoid-adresses in the DCC format switchable
Software Version 2 allows you to allocate symbols for points and signals
Memory for 16 routes. Each of these routes can have 10 steps. Solenoid-Addresses 1-2048
Max. Output: 2 A
Programming track output for DCC decoders
LNCV programming for LocoNet components
Output for a Reversing Loop Relay 61080 for the automatic Control a terminal loop
LocoNet T-connector for all LocoNet devices
LocoNet B port for external LN boosters such as Power 4 or Power 8
With RailCom? CutOut in the DCC signal as for the automation system MARCo
Dispatch mode for FRED Hand controller
Updateable via USB-LocoNet Interface 63120 or through the interface in an intellibox.


Read more...
Stock:
Available from shops: Stroud: 1(explain)
(Prod Ref #45290)
Price: £215.00


More info

Lenz Start Set 100 Digital Control System 60100

The Lenz-developed data communications system formed the basis of the first NMRA standards for DCC. The company has always been at the forefront of development and Lenz systems remain popular with experienced users.

Set 100 is a starter set comprising one LH100 walk-around handset, a LVZ100 5 amps command station/amplifier and full instruction manuals for setup and operation of the system. Note : A mains transformer is required.

The LH100 is a tethered (cable connected) walk-around handset with a push-button keypad. A calculator style numerical pad is provided for locomotive or accessory decoder selection, with fucntion control selector alongside. Above this are the direction and speed control buttons, with slow step-by-step (for pulling away from a station) or rapid (to get trains out of the fiddle yard quickly) acceleration/deceleration options. The LCD screen display provides a full reading of the speed/direction and function status of the locomotive being controlled

4 digit addressing is available, giving control of up to 256 locomotive and 999 accessory decoders. All forms of programming are supported including advanced one step address programming. The numerical keypad makes CV programming with the LH100 easier than with the LH90 and detailed functions can be defined. The LH100 can create momentary functions on a per function per locomotive basis and XpressNet handsets including the knob control LH90 can take advantage of any available momentary functions once set up.
The LZV100 command station will support up to 31 handsets from Lenz or any other manufacturer using the Lenz XpressNet system.

The Set 100 is recommended for DCC enthusiasts wanting to exploit full decoder configuration capabilities. LH90 and other XpressNet handsets can be added as control handsets, only one LH100 handset is needed as the 'master' for programming.


Read more...
Stock:
Pre-Order (Website:0)(explain)
(Prod Ref #45289)
MRP: £342.95
Antics Price: £290.00


More info

Lenz USB & Ethernet LAN Interface 23151

In addition to the USB port the new Digital plus interface offers an Ethernet gateway for connecting the system to a PC or to a router. Thus some interesting new options are available such as, for example, wireless control with an iPod or an iPhone.

Connect the new interface via XpressNet to the command station and via Ethernet to a router. Now you can control your model railway wireless with your iPhone or iPod and the software TouchCab which is particularly customised for Digital plus purposes.

Of course our new interface provides also features like CV editor and PC control panel.


Read more...
Stock:
Pre-Order (Website:0)(explain)
(Prod Ref #52161)
MRP: £155.95
Antics Price: £135.00


More info

NCE The Power of DCC Automatic Program Track Adaptor for Power Cab 5240226

NCE The Power of DCC Automatic Program Track Adaptor for Power Cab 5240226
Adds a separate program track to Power Cab system. Prevents accidental programming of ALL locos on your track when using Program Track mode. Automatically disconnects your main line when in Program Track mode but does not affect Program on Main. Compatible with all DCC systems.
Read more...
Stock:
Website: 1(explain)
(Prod Ref #100968)
Price: £20.00

> Power & Electrics > Digital Command Control (DCC) > DCC Control Units
 
Antics on-line with model shops in: Stroud (HQ), Bristol, Cardiff, Gloucester, Plymouth and Coventry.
We stock a full range which includes plastic kits, radio control cars, diecast models, railways, planes and boats etc.
Click on the links under "Available to buy now" or any picture in order to start shopping. Offers subject to availability. E&OE.
Jatech Limited