Antics Models, Diecast, Radio Control and Model Railways
  1. Antics Online Model Railways Power & Electrics Electric Point Control

Peco PL-10 Point Motor

Peco PL-10 Point Motor

This motor attaches directly to the underside of the point to ensure positive and reliable operation. Requires a 40 x 25mm hole in the baseboard to accommodate the motor. Operation is from a passing contact switch or probe and stud system to give a pulse from the 16v AC outlet found on most transformers (2 amps required). If this isn't available an uncontrolled 12v DC supply may suffice.
Use only a pulse as applying a constant current would burn out the motor.
£8.95
MRP £8.95

Bristol: 6, Plymouth: 5
Delivery from stores takes a few days longer!
(Product Ref 31748)
Cookies are disabled.
To place an order please call 01453 377030
Have a question about this product? Let us know
Contact us
Have a question about this product? Let us know
Contact us
Related Products
Provides the short burst of current required to operate the PL-11 and PL-10 series of Turnout Motors. The PL-31 Connectors are ideal for attaching the PL-34 Wiring Looms or PL-38 wire to these switches without soldering; the included Shrouds prevent current 'shorting out' between the terminals.
Peco Passing Contact Switch Red Lever PL-26R
£9.50
Provides the short burst of current required to operate the PL-11 and PL-10 series of Turnout Motors. The PL-31 Connectors are ideal for attaching the PL-34 Wiring Looms or PL-38 wire to these switches without soldering; the included Shrouds prevent current 'shorting out' between the terminals.
Peco Passing Contact Switch White Lever PL-26W
£9.50
Provides the short burst of current required to operate the PL-11 and PL-10 series of Turnout Motors. The PL-31 Connectors are ideal for attaching the PL-34 Wiring Looms or PL-38 wire to these switches without soldering; the included Shrouds prevent current 'shorting out' between the terminals.
Peco Passing Contact Switch Black Lever PL-26B
£9.50
Provides the short burst of current required to operate the PL-11 and PL-10 series of Turnout Motors. The PL-31 Connectors are ideal for attaching the PL-34 Wiring Looms or PL-38 wire to these switches without soldering; the included Shrouds prevent current 'shorting out' between the terminals.
Peco Passing Contact Switch Yellow Lever PL-26Y
£9.50
A simple yet effective method of switching turnouts. The PL-18 Studs are inserted into the control panel, often laid out as a layout diagram. A wire is then soldered to the tag at the back, which goes to the relevant solenoid of the turnout motor. When power is applied by touching the powered PL-17 probe on the stud the Turnout Motor is activated.
Peco Probe for electrically operating Points PL-17
£6.25
A simple yet effective method of switching turnouts. The PL-18 Studs are inserted into the control panel, often laid out as a layout diagram. A wire is then soldered to the tag at the back, which goes to the relevant solenoid of the turnout motor. When power is applied by touching the powered PL-17 probe on the stud the Turnout Motor is activated.
Peco Studs and Tag Washers PL-18
£5.50
Attaches directly to the PL-10 family of Turnout Motors with contact adhesive. This single pole switch can control frog polarity, ground signals etc. PL-31 Spade Connectors can be used to attach wires to these units without the need for soldering.
Peco Accessory Switch PL-13
£5.25
Antics recommended for ease of installationThe Peco capacitor discharge unit is supplied in a neat plastic box with quick clamp type connectors, ready for installation without needing further protection.The capacitors provide sufficient instantaneous energy to positively throw point motors.
Peco Capacitor Discharge Unit CDU PL-35
£24.95
A pack of 20 self-adhesive cable clips, ideal for keeping wiring under control under layouts and inside larger models.
Peco Self-Adhesive Cable Clips Pack of 20 PL-37
£4.50
Makes wiring the PL-10 series of Motors quick and easy. Just a simple push fit onto the motor terminals; the other ends are tinned and ready for the PL-39 Terminal Block, PL-50 Switch Module Unit, or PL-31 Push on Terminal Connectors.Pack of 2 looms.
Peco Wiring Loom for Peco Point Motors PL-34
£6.95
Control switch and wiring harness for connection to Peco point motors. Switch and point motor harness are supplied complete wiith connectors for the EZE-Wire system, allowing extensions to be added between the switch and motor to reach the point motor location. Heat-shrink tubing is supplied to protect and insulate joints.EZE-Wire - Plug and Play layout wiring from Expo.The EZE-Wire system uses pre-made cabling complete with spade connectors on the ends to allow point motor cabling to be installed quickly and easily. No soldering required.
Expo EZE-Wire Point Switch with Peco Point Motor Harness 28070
£4.99